Altec Lansing Industrial Professional Sound Products Spec site

ALTEC LANSING INDUSTRIAL PROFESSIONAL SOUND PRODUCTS POWERED MIXER LIST

Altec Powered Mixers

 

 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION

PS2100A Powered Mixing Console

page 2

 

<< Previous

The mixer also contains two auxiliary input channels for high-impedance line or tape sources. These channels have independent monitor sends, pan pots, and slide faders.

SPECIFICATIONS (continued)

Measurement Conditions
1. All noise measurements are made through mic inputs with 150-ohm source, 20 Hz - 20 kHz noise bandwidth.
2. 0 dBu = 0.775 Vrms

Input Equalization:
Low: t15 dB at 100 Hz Mid: t12 dB at 3 kHz High: ±15 dB at 10 kHz

Output Equalization: ±12 dB at the following ISO centers 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz, 8 kHz

Effects Send Output Level:
High: +4 dBu (nominal line level)
Low: -16 dBu (nominal instrument level)

Phantom Power Voltage: +48 Vdc

Dimensions:
Height: 8 inches (20.3 cm)
Width: 20 inches (50.8 cm)
Depth: 19 inches (48.3 cm)

Weight: 36 lbs (16.3 kg)

Power Requirements:
Standard Unit: 100/120 Vrms (switchable), 60 Hz, 400 W
Export Unit: 220/240 Vrms (switchable), 50 Hz, 400 W

ARCHITECT'S and ENGINEER'S SPECIFICATION

The powered mixing console shall be a stereo mixer with ten inputs and two built-in 150-watt (peak) per channel power amplifiers. The unit shall have a balanced, lightweight, and durable chassis with a recessed front panel for control knob protection.
The mixer shall consist of eight input channels, each of which may be used as either a balanced mic input or a high-impedance line input. Each of these channels shall have a gain control with a clip LED, an independent monitor send, a three-band equalizer, an effects-reverb send, a pan pot, and a slide fader. The mixer shall also contain two auxiliary input channels for high-impedance line or tape sources. These channels shall have independent monitor sends, pan pots, and slide faders.
The master section of the mixer shall have two power amplifiers, two eight-band equalizers, peak-limited spring reverb, and master reverb level controls. A stereo/mono mode switch shall allow switching between normal stereo operation and mono with monitors. The mode switch shall assign amplifiers and equalizers with no required patching.
The mixer shall meet the following performance criteria. Power output, single channel: 100 watts average continuous power into 8 ohms at 1 kHz. Power output, single channel: 150 watts peak power into 4 ohms with IHF dynamic headroom test signal at 1 kHz. Minimum load impedance: 4 ohms per channel. THD (mixer output): < 0.02% at +4 dBu typical;
< 0.05% maximum. THD (amplifier output): < 0.02% at 100 watts into 8 ohms at 1 kHz typical; < 0.05% maximum. Signal to noise ratio: 100 dB below full amplifier output (20 Hz - 20 kHz) with all faders down. Absolute output noise at mixer output: -70 dBu (20 Hz - 20 kHz) with all faders at nominal setting and a gain of 44 dB. Equivalent input noise: -115 dBu (20 Hz - 20 kHz) measured at preamp output and maximum gain. Maximum input level of low-impedance inputs: +6 dBu (1.5 Vrms). Maximum input level of high-impedance inputs: +26 dBu (19.95 Vrms). Maximum input level of auxiliary inputs +10 dBu (3.16 Vrms). Input low frequency equalization: ±15 dB at 100 Hz. Input mid-frequency equalization: ±12 dB at 3 kHz. Input high frequency equalization: ±15 dB at 10 kHz. Output equalization gain and ISO center frequencies: ±12 dB at 63 Hz, 125 Hz, 250 Hz, 500 Hz, 1 kHz, 2 kHz, 4 kHz, and 8 kHz. Effects send high output level: +4 dBu (nominal line level). Effects send low output level: -16 dBu (nominal instrument level). Phantom power voltage: +48 Vdc. Dimensions: 8 inches (20.3 cm) high, 20 inches (50.8 cm) wide, 19 inches (48.3 cm) deep. Weight: 36 pounds (16.3 kg). Power requirements: standard configuration 100/120 Vrms (switchable), 60 Hz, 400 watts; optional configuration 220/240 Vrms (switchable), 50 Hz, 400 watts.
The mixer shall be the ALTEC LANSING PS2100A powered mixing console.

Next >>

 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION

aLTEC aMPLIFIER aCCESSORIES SECTION Altec Amplifier Section Altec Microphone section  
Altec Powered Mixers and Misc
Altec Signal Processing sections
 
Specifications Catalog Table of Contents

 

 

 

CLICK ON ANY IMAGE TO VIEW THAT EQUIPMENT SECTION